Difference between revisions of "Software:Generic CADD"
m |
|||
| (13 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
Generic CADD can run full screen and, on a wide-screen monitor, Generic CADD can run without distortion even though it was designed for conventional CRT monitors (aspect ratio 4:3). First set the DOSBox configuration file for fullscreen: | Generic CADD can run full screen and, on a wide-screen monitor, Generic CADD can run without distortion even though it was designed for conventional CRT monitors (aspect ratio 4:3). First set the DOSBox configuration file for fullscreen: | ||
| − | + | fullscreen=true <br> | |
| − | + | fulldouble=false <br> | |
| − | + | fullresolution=original <br> | |
| − | + | windowresolution=original <br> | |
| − | + | output=surface <br> | |
| − | + | autolock=true <br> | |
| − | + | sensitivity=100 <br> | |
| − | + | waitonerror=true <br> | |
| − | + | priority=higher,normal <br> | |
| − | + | mapperfile=mapper-0.74.map <br> | |
| − | + | usescancodes=true <br> | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | <p>If the RA command doesn't exist, which may be the case for Generic CADD version 6.0.0, set the ratio of the two numbers in line 72 of the environment file | + | language= <br> |
| + | machine=svga_s3 <br> | ||
| + | captures=capture <br> | ||
| + | memsize=16 <br> | ||
| + | |||
| + | frameskip=0 <br> | ||
| + | aspect=false <br> | ||
| + | scaler=none <br> | ||
| + | |||
| + | <p> Then set Generic CADD to run in video mode 106h with the VESA16.vgd driver or 107h with the VESA256.vgd driver (or to a lower resolution, if necessary). Generic CADD has a command — RA — to adjust for the screen aspect ratio. When you execute the command, two lines are shown on the screen and you enter the measured lengths of the lines (nominally the width and height of the screen) or you can enter the screen aspect ratio, e.g. "8" and "5". This will adjust Generic CADD so that circles are round and squares, square.</p> | ||
| + | |||
| + | <p>If the RA command doesn't exist, which may be the case for Generic CADD version 6.0.0, set the ratio of the two numbers in line 72 of the environment file — "environ.fil" — (normally "8.750000 6.750000") to the aspect ratio of the screen, e.g. "16.000000 9.000000."</p> | ||
Latest revision as of 17:07, 26 February 2013
Generic CADD can run full screen and, on a wide-screen monitor, Generic CADD can run without distortion even though it was designed for conventional CRT monitors (aspect ratio 4:3). First set the DOSBox configuration file for fullscreen:
fullscreen=true
fulldouble=false
fullresolution=original
windowresolution=original
output=surface
autolock=true
sensitivity=100
waitonerror=true
priority=higher,normal
mapperfile=mapper-0.74.map
usescancodes=true
language=
machine=svga_s3
captures=capture
memsize=16
frameskip=0
aspect=false
scaler=none
Then set Generic CADD to run in video mode 106h with the VESA16.vgd driver or 107h with the VESA256.vgd driver (or to a lower resolution, if necessary). Generic CADD has a command — RA — to adjust for the screen aspect ratio. When you execute the command, two lines are shown on the screen and you enter the measured lengths of the lines (nominally the width and height of the screen) or you can enter the screen aspect ratio, e.g. "8" and "5". This will adjust Generic CADD so that circles are round and squares, square.
If the RA command doesn't exist, which may be the case for Generic CADD version 6.0.0, set the ratio of the two numbers in line 72 of the environment file — "environ.fil" — (normally "8.750000 6.750000") to the aspect ratio of the screen, e.g. "16.000000 9.000000."
