Difference between revisions of "Software:Generic CADD"

From DOSBoxWiki
Jump to: navigation, search
m
Line 2: Line 2:
  
 
<p> fullscreen=true </p>  
 
<p> fullscreen=true </p>  
fulldouble=false  
+
<p> fulldouble=false </p>
fullresolution=original  
+
<p> fullresolution=original </p>
windowresolution=original  
+
<p> windowresolution=original </p>
output=surface  
+
<p> output=surface </p>
autolock=true  
+
<p> autolock=true </p>
sensitivity=100  
+
<p> sensitivity=100 </p>
waitonerror=true  
+
<p> waitonerror=true </p>
priority=higher,normal  
+
<p> priority=higher,normal </p>
mapperfile=mapper-0.74.map  
+
<p> mapperfile=mapper-0.74.map </p>
usescancodes=true  
+
<p> usescancodes=true </p>
 +
<p> </p>
 +
<p> language= </p>
 +
<p> machine=svga_s3 </p>
 +
<p> captures=capture </p>
 +
<p> memsize=16 </p>
 +
<p> </p>
 +
<p> frameskip=0 </p>
 +
<p> aspect=false </p>
 +
<p> scaler=none</p>
 +
<p></p>
 +
<p> Then set Generic CADD to run in video mode 106h with the VESA16.vgd driver or 107h with the VESA256.vgd driver (or to a lower resolution, if necessary).  Generic CADD has a command -- RA -- to adjust for the screen aspect ratio.  When you execute the command, two lines are shown on the screen and you you enter the measured lengths of the lines (nominally the width and height of the screen). This will adjust Generic CADD so that circles are round and squares, square.</p>
  
language=
+
<p>If the RA command doesn't exist, which may be the case for Generic CADD version 6.0.0, set the ratio of the two numbers in line 72 of the environment file, "environ.fil", (normally "8.750000 6.750000") to the aspect ratio of the screen, e.g. "16.000000 9.000000."</p>
machine=svga_s3
+
captures=capture
+
memsize=16
+
 
+
frameskip=0
+
aspect=false
+
scaler=none
+
 
+
Then set Generic CADD to run in video mode 106h with the VESA16.vgd driver or 107h with the VESA256.vgd driver (or to a lower resolution, if necessary).  Generic CADD has a command -- RA -- to adjust for the screen aspect ratio.  When you execute the command, two lines are shown on the screen and you you enter the measured lengths of the lines (nominally the width and height of the screen). This will adjust Generic CADD so that circles are round and squares, square.
+
 
+
If the RA command doesn't exist, which may be the case for Generic CADD version 6.0.0, set the ratio of the two numbers in line 72 of the environment file, "environ.fil", (normally "8.750000 6.750000") to the aspect ratio of the screen, e.g. "16.000000 9.000000."
+

Revision as of 18:27, 23 February 2013

Generic CADD can run full screen and, on a wide-screen monitor, Generic CADD can run without distortion even though it was designed for conventional CRT monitors (aspect ratio 4:3). First set the DOSBox configuration file for fullscreen:

fullscreen=true

fulldouble=false

fullresolution=original

windowresolution=original

output=surface

autolock=true

sensitivity=100

waitonerror=true

priority=higher,normal

mapperfile=mapper-0.74.map

usescancodes=true

language=

machine=svga_s3

captures=capture

memsize=16

frameskip=0

aspect=false

scaler=none

Then set Generic CADD to run in video mode 106h with the VESA16.vgd driver or 107h with the VESA256.vgd driver (or to a lower resolution, if necessary). Generic CADD has a command -- RA -- to adjust for the screen aspect ratio. When you execute the command, two lines are shown on the screen and you you enter the measured lengths of the lines (nominally the width and height of the screen). This will adjust Generic CADD so that circles are round and squares, square.

If the RA command doesn't exist, which may be the case for Generic CADD version 6.0.0, set the ratio of the two numbers in line 72 of the environment file, "environ.fil", (normally "8.750000 6.750000") to the aspect ratio of the screen, e.g. "16.000000 9.000000."